waterproof IP67 RGB Led channel letter 12mm LED pixel string light Dc5V AIA-1 manufacturer from China Shenzhen Centuryled Co., Ltd

waterproof IP67 RGB Led channel letter 12mm LED pixel string light Dc5V

Place of Origin:

Guangdong, China (Mainland)


	Add to My Favorites
HiSupplier Escrow	Share \|

Product Detail

Model No.: AIA-1

Waterproof IP67 RGB Led channel letter 12mm LED Pixel String light Dc5V
<s

Waterproof IP67 RGB Led channel letter 12mm LED Pixel String light Dc5V

description:

RGB Pixels are digitally-controllable lights you can set to any color, or animate. Each RGB LED and controller chip is molded into a 'dot' of silicone. The dots are waterproof and rugged. There are four flanges molded in so that you can 'push' them into a 12mm drill hole in any material up to 1.5mm/0.06" thick. They're typically used to make outdoor signs. Compared to our other 20mm LED dots, these are diffused 8mm LEDs so they are not as bright but they color mix a little nicer.

1.This pixel LED is 50pcs per string.8cm wire between each LED,wire size:20AWG.Punching Diameter is 12mm.

2.We have three different IC Model for this LED,Please note different IC have different Wire define.

3.Controller:we usually select SD Controller,you also could use DMX controller which could support WS2801 or LPD6803 chip.

4.it works with DC5V only,and supply the power to LED chain every string(50pcs max),make sure the Voltage is the same in both side of LED chain.

5.This product can carry out effects of full-color running water,chasing and scanning ,it is easy installation, high brightness, safe and energy conservation, long lifespan,low brightness declines,Widely used in LOGO,advertisement bill board exposed luminous characters,painted screen, can replace the traditional neno signs, the spacing between lamps can be chosed according to the building height.

Specification:

Model NO.	SJ-12-CRGB
Power Consumption	0.3W
Work Voltage	DC5V
Beam Angle	≥120
LED Quantity	1pcs
Color	Full color(ICRGB)
chip material	epistar
Waterproof Grade	IP66
Work Temperature	-40-60°C
Life-span	50,000H
Certificate	CE&RoHS
Warranty	2 years

Parameter

RED WIRE: DC5V input +

yellow wire:DATA

greem wire: clock

blue: Ground

input side: is the side with IC

RGB Pixels are digitally-controllable lights you can set to any color, or animate. Each RGB LED and controller chip is molded into a 'dot' of silicone. The dots are waterproof and rugged. There are four flanges molded in so that you can 'push' them into a 12mm drill hole in any material up to 1.5mm/0.06" thick. They're typically used to make outdoor signs

Each dot is digitally controlled, with an internal 8-bit PWM LED driver (24-bit color for 16 million different shades). The pixels must be clocked by a microcontroller, we have an example code linked below that works on an Arduino, it should be simple to adapt it to any other microcontroller.

The pixels use 8mm diffused RGB LEDs, with a 120 degree beam width. The total max brightness of all LEDs is about 1600mcd but with the light more evenly distributed & mixed than a clear LED

12mm diameter (0.45") 75mm deep (1.5")

100mm

50 pieces per strand

These pixels use a WS2801 chip for full 24 bit color

5V power, 60mA maximum per pixel (LED on full white)

2-pin SPI-like protocol

WS2801 Datasheet for the chip inside each pixel

Brightness: Red = 3.3 Lumens/300 mcd, Green = 10 Lumens/1000 mcd, Blue = 2.7 Lumens/300 mcd (mcd calculation based on full 120 degree beam)

Application:

Widely used for home decoration use, hotels, clubs, shopping malls

Architectural decorative lighting, boutique atmosphere lighting

Extensively applied in Backlighting, concealed lighting, channel letter lighting